Tomato Wireless Mode Access Point mode is used for a basic wireless access point. You setup a wireless SSID and password and simply connect. This mode has no bridging functionality. The Linksys Wireless-G Access Points can be configured as an Access Point, Access Point Client, Wireless Repeater, and Wireless Bridge. The Wireless Repeater mode will turn the access point into a wireless repeater to extend the range of your signal. The WAP54G will work as a wireless repeater with the following devices. Access point power settings help dictate how large a coverage area each access point is responsible for. If coverage cells are too large and have major overlap with each other, it can cause roaming issue where devices stay stuck to access points that are further away even though there are access points nearby that have a stronger signal. This is effected by getting access to the router's advanced settings and configurations. When looking for the best router for tomato firmware, several things feature to make up the best router. Most of the routers come on the higher end, making it a little bit difficult to acquire.
I found a setup that I like even better than my previous one. I have highlighted the main differences, in red, below.
To set it up as repeater do the following: Faronics_dfs licence key free download.
- Do a 30 second reset
Under wireless->basic settings:
- Wireless mode: AP
- Wireless Network Name (SSID): Your prefer SSID
- Wireless Channel: Your prefer channel ( Use channel with less interference from other access point)
- Save Settings
Under Wireless > Wireless Security
- Set your wireless authentication
Under Setup->Basic Setup:
- Under WAN Connection Type:
- Connection Type : Disabled
- STP : Disable
- Under Router IP:
- Local IP address :Set your IP your address to a same subnet of your main router (if your main router IP is 192.168.1.1, set it to same subnet like 192.168.1.2)
- Subnet Mask : same as your main router subnet
- Gateaway : Your main router IP
- DNS : Your main router IP
- Under Network address Server Setting (DHCP)
- DHCP Type : DHCP Forwarder
- DHCP Server : Your main router IP
- Time settings : disable
- Save Settings
Under Security Tab
- Un-check all items in the 'Block WAN Request' section
- Then disable the SPI firewall
- Save Settings
Under Administration Tab
- Enter all other necessary information, remember to change your password
- Click the Save button
- Then click Reboot button
Tomato As Access Point
Wireless Bridge Mode
In this section, we'll discuss how to choose a wireless bridge mode for your Tomato network. A wireless bridge connects two or more LAN segments over a wireless link. Tomato offers various modes, including: Access Point, Access Point + WDS, Wireless Client, Wireless Ethernet Bridge, and WDS (Wireless Distribution System).
Some routers offer a 'client' or 'bridge' mode. Others offer a 'repeater' mode. And then there is WDS. Currently, Tomato firmware does not offer a wireless repeater mode. However, it does offer a ‘Access Point + WDS' mode, which does virtually the same thing.
Access Point mode is used for a basic wireless access point. You setup a wireless SSID and password and simply connect. This mode has no bridging functionality.
Access Point + WDS mode can be used as both a wireless access point and a wireless bridge.
Wireless Client mode allows for the router to connect to another router as a ‘client'. In client mode, the router will not retransmit wireless signal. However, in client mode, the router can share Internet access with other client devices but they must be connected to the router with an Ethernet cable. In client mode, router maintains a separate subnet and manages its own IP address pool.
Wireless Ethernet Bridge mode works similar to ‘client' mode. The main difference is that the router handles DHCP and IP addresses for both routers. Again, this mode does not retransmit wireless signal but you can connect additional devices using the Ethernet ports on the back of the router.
WDS (Wireless Distribution Mode) is a wireless bridge mode that connects two or more routers by exchanging MAC addresses.
TIP: The wireless modes that we discuss in this section may behave differently based on the router and firmware mod that you are using. If you do not see the wireless options demonstrated in this section, you may need to upgrade your firmware to a different mod. For this demonstration, I'm using the VPN mod built by ‘Shibby'. The AIO (All in One) mod also offers these options.
Do you have a two or three story home? Do you have a guest house, garage, or other building that needs Internet access? A wireless bridge might be just what you need. Connecting two routers over a wireless bridge isn't much more difficult than a wired connection. I'll show you how to create one shortly but before we do that, let's knock out some basics.
Tomato Wireless Bridge Network
A wireless bridge connects two LAN segments using a wireless link. This is known as a 'point-to-point' wireless bridge, also called a wireless LAN to LAN bridge.
- Under WAN Connection Type:
- Connection Type : Disabled
- STP : Disable
- Under Router IP:
- Local IP address :Set your IP your address to a same subnet of your main router (if your main router IP is 192.168.1.1, set it to same subnet like 192.168.1.2)
- Subnet Mask : same as your main router subnet
- Gateaway : Your main router IP
- DNS : Your main router IP
- Under Network address Server Setting (DHCP)
- DHCP Type : DHCP Forwarder
- DHCP Server : Your main router IP
- Time settings : disable
- Save Settings
Under Security Tab
- Un-check all items in the 'Block WAN Request' section
- Then disable the SPI firewall
- Save Settings
Under Administration Tab
- Enter all other necessary information, remember to change your password
- Click the Save button
- Then click Reboot button
Tomato As Access Point
Wireless Bridge Mode
In this section, we'll discuss how to choose a wireless bridge mode for your Tomato network. A wireless bridge connects two or more LAN segments over a wireless link. Tomato offers various modes, including: Access Point, Access Point + WDS, Wireless Client, Wireless Ethernet Bridge, and WDS (Wireless Distribution System).
Some routers offer a 'client' or 'bridge' mode. Others offer a 'repeater' mode. And then there is WDS. Currently, Tomato firmware does not offer a wireless repeater mode. However, it does offer a ‘Access Point + WDS' mode, which does virtually the same thing.
Access Point mode is used for a basic wireless access point. You setup a wireless SSID and password and simply connect. This mode has no bridging functionality.
Access Point + WDS mode can be used as both a wireless access point and a wireless bridge.
Wireless Client mode allows for the router to connect to another router as a ‘client'. In client mode, the router will not retransmit wireless signal. However, in client mode, the router can share Internet access with other client devices but they must be connected to the router with an Ethernet cable. In client mode, router maintains a separate subnet and manages its own IP address pool.
Wireless Ethernet Bridge mode works similar to ‘client' mode. The main difference is that the router handles DHCP and IP addresses for both routers. Again, this mode does not retransmit wireless signal but you can connect additional devices using the Ethernet ports on the back of the router.
WDS (Wireless Distribution Mode) is a wireless bridge mode that connects two or more routers by exchanging MAC addresses.
TIP: The wireless modes that we discuss in this section may behave differently based on the router and firmware mod that you are using. If you do not see the wireless options demonstrated in this section, you may need to upgrade your firmware to a different mod. For this demonstration, I'm using the VPN mod built by ‘Shibby'. The AIO (All in One) mod also offers these options.
Do you have a two or three story home? Do you have a guest house, garage, or other building that needs Internet access? A wireless bridge might be just what you need. Connecting two routers over a wireless bridge isn't much more difficult than a wired connection. I'll show you how to create one shortly but before we do that, let's knock out some basics.
Tomato Wireless Bridge Network
A wireless bridge connects two LAN segments using a wireless link. This is known as a 'point-to-point' wireless bridge, also called a wireless LAN to LAN bridge.
Wireless Bridge
Advanced Tomato Access Point
In a real bridge environment, the transmitters only communicate with each other. A true bridge does not communicate with clients at all. The bridge merely connects the two networks and enables wired clients to connect to their LAN ports. Therefore, they do not re-transmit to wireless clients. If you want to re-transmit wireless signal with Tomato, you'll need to use 'Access Point + WDS' mode.
Be advised that these bridge options are not found on all routers. Both, DD-WRT and Tomato firmware offer wireless bridge capabilities which is one reason they've become so popular. DD-WRT has posted a feature comparison chart that may help you understand this better.
What are the drawbacks of a wireless bridge?
There is a downside to using a wireless bridge in repeater mode and WDS mode. If the secondary router retransmits the wireless signal (instead of connecting client computers with a wire), the wireless throughput in the secondary building will be cut in half. Each transmission is known as a 'hop'. The second wireless hop is the one that takes the hit. In the image below, you can see that the laptop connects at a much slower speed.
Access Point Toronto
Basically, wireless clients connected to the second router will not enjoy the same performance as the wireless clients connected to the first router. Why? Because the transmitter in the second router has to do twice the work. It must first receive the signal from the primary router, and then retransmit the signal to wireless clients.
Tomato Access Point Firmware
If devices in the secondary building are simply browsing the Internet and streaming music, you'll be fine. If however, you plan to stream huge files, HD videos and play games online at the same time, you might experience less than par service. In this case, make sure you have routers with enough power to handle the job. Two wireless-N (802.11n) or wireless-AC (802.11ac) routers would ideal. With two extremely fast routers, you'll hardly notice the difference. And with today's dual-band routers, you can decrease the impact of the second ‘hop' even further. Simply dedicate one frequency band to the bridge, and dedicate the other frequency band to your clients.
